Tool sửa ổ cứng Seagate

Tool sửa ổ cứng Seagate là thiết bị sửa ổ cứng Seagate bao gồm phần cứng và phần mềm kèm theo. Chuyên dùng sửa ổ cứng Seagate bị lỗi firmware, sửa ổ cứng Seagate lỗi Rom, sửa ổ cứng Seagate bị bad.

Tool sửa ổ cứng Seagate

  • Mã SP:DFL-SRP - SG
  • Giá bán:26,000,000 vnđ Đặt mua

Tool sửa ổ cứng Seagatethiết bị sửa ổ cứng Seagate bao gồm phần cứng và phần mềm kèm theo. Chuyên dùng sửa ổ cứng Seagate bị lỗi firmware, sửa ổ cứng Seagate lỗi Rom, sửa ổ cứng Seagate bị bad.

Mặc dù có tài liệu hướng dẫn kèm theo nhưng đó chỉ là hướng dẫn cơ bản cách vận hành mà thôi. Tuy nhiên trên forum có sự chia sẻ của các kỹ thuật viên với nhau. Lẽ đương nhiên bạn phải mua sản phẩm thì mới có quyền truy cập vào đó.

Thiết bị sửa ổ cứng Seagate này hổ trợ các dòng sản phẩm sau:

5400.6, 7200.4, 7200.11, 7200.12, 7200.14, 7200.10, 7200.9, 7200.8, 7200.7. Sau đây là các tính năng của nó tool sửa ổ cứng seagate này:

1, ATA & COM ports are both supported;

2, Easy repair of LBA=0 & Capacity=0;

3, Easy repair of busy drives;

4, Easy repair of partial sector access drives;

5, Easy repair of DOS/SMART/MCMT error;

6, Easy repair of SYS error 1009;

7, Easy repair of ready-then

8, Easy password removal,

9, F3 firmware modules read/write/edit by ATA &

10, Track, CP and SA read/write/edit;

11, ROM and ROM modules read/write/edit;

12, Password set and remove

13, Adaptive ROM regeneration for successful head swap;

14,To write common firmware resources and key data recovery modules is supported to

repair many drives with unknown or complete firmware failures of F3 drives;

15, CAP/RAP/SAP read/write/edit;

16, P-list editing/deleting abnormal defects is supported;

17, SYS file read/write/editing by ATA and COM are supported;

18, Bad sector scan and LBA to Head number conversi

19, F3 bad sector repair is supported;

20, Sector read/editing is supported;

21, NHPA, soft reset, hard reset,start/stop motor and other common ATA commands;

22, G-list/P-list/NG-list/SLIP list processing;

23, Head correction and adjust h

24, Common Firmware generation(LOD file generation);

25, Zone repair;

26, Initialize/Edit HDD ID;

27, NG list clearing (by COM port) for new F3 drives;

28, Customize offline commands processing;

29, Independent channel operation mode wit

30, Set Max LBA.

Nhà sản xuất: http://www.dolphindatalab.com

Cảm tạ Chúa!

Bình luận (0)

Gửi bình luận của bạn

Captcha

.

 

Tin Hot nhất

Thống kê lượt xem

Tổng truy cập 1,709,264

Đang online2